Allison 2000 Transmission parts, repair guidelines, problems, manuals
LCT2000, Allison 2400
Transmission general data
| Number of gears | Transmission Type | Torque (Nm) | ATF (full capacity) L | ATF (change) L | ATF type |
|---|---|---|---|---|---|
| 5 | AT | 841 | 14 | 10 | Allison TES 295 |
What are you looking for?
Overhaul Kit | Friction Kit | Friction | Steel Plate | Steel Kit | Band | Solenoid Kit | Solenoid EPC | Solenoid TCC | Pump | Shaft | Drum | Valve body | Torque converter | Hub | Piston | Piston Kit | Planetary Gear | Filter | Gasket | Bushing | Seal | Bearing | Pressure Plate | Stator | Differential | Retainer | Inhibitor Switch | Instruction manual | TOOLS & ACCESORIES | Sensor
-
-
- Bellhousings
- Cover Bolt, Cover Bolts, Mounting Bolt, Mounting Bolts, Pan Bolt, Pan Bolts, stud, studs, Split Pin
- Case Covers, Cover, Dust Cover,
- Dampers, Damper Assembly, Damper
- Flexplates, Flex plate, Driveplate, Drive plate, D/Plate, Flexplate
- TCMs, transmission control module, TCU, TCM, Computer, Circuit Board, Control Module, Control Unit, Hardware
- Filters, Filter Cartridges, Filter Cartridge, Oil Pan Filter, Inlet, Filter Kit
- Friction Discs, Frictions, fric, Friction Disc, Friction, Friction Plate, Friction Ring, fric., Clutch Plate, Friction Lining
- Gaskets, gsk, gskt, , Cover Gasket, Cover Gaskets, Case Gasket, Case Gaskets, Filter Gasket,Filter Gaskets
- Hubs, Hub Insert
- o-ring, o ring, 0ring, 0-ring, 0 ring, ORing, Ring, O-Rings, o-ring, O'Ring
- ohk, OHK kit, Overhauls, mok, Overhaul kit, Masterkit, Master kit, Master Overhaul, Repair package, Overhaul, Rebuild kit, Master Rebuild, Super Rebuild Bundle, Banner Kit, SUPER KIT, SUPERIOR KIT
- Pans, Crankcase, Oil Pan
- Performance Converters
- Pistons, Apply Piston, Pack Piston, High Piston, Damper Piston, Piston Damper, Piston Plate, Interm. Servo Pist, Piston Seals, Piston Seal Ring, Piston Seal Rings, Piston Seal, Piston Cover, Piston Covers, Rear Servo, servo piston, Piston Retainer, Piston Retainers, Servo kit, Super Servo, servo, Shift Pison
- Piston Kits, Piston Complete, Piston part, Piston Sets, Piston Set
- Seals, Metal clad seal, Lip Seals, Connector Hole Seal, Lip Seal, Main Seal, Radial Lip Seal, Main Seal, Manual Seal, Oil Feed Seal, Side Cover Seal, Seal Cooler, Seal Oil Cooler, Case Seal
- Pump seal
- Cap,
- Springs, Wave Spring, Spring Adjuster, Spring Disc, Torsion Spring, Return Spring, Piston Spring, Damper Spring, Damper Springs, Control Spring, Detent Spring, Drum Spring, Limit Spring, Return Sprng, Diaphragm Springs, Diaphragm Spring
- Stators
- Steel Kits, Steel Set Kit, Steel Clutch Plate Kit, Steel kit, clutch steel, clutch steels, Steel set, steel pack, module kit, Steel Plate Clutch Kit, Steel Plate Kit, Steel Plate Module, Steel Plate Set, Steel Module
- Steel Plates, steel, Steels, steel disk
- converter, t.converter,
- Turbines
- Throttle Valve, Timing Valve, Operating, Relief Valve, Safety Valve, Control Valve, AFL Valve, Limit Valve, Actuator Feed Limit Valve, AFL Valve
- VB plate, Valve body plates, Valve body plate, ValveBody, V/Body, valve-body, v body, v-body, v/b, Orifice, Hydraulic control unit, HCU
Technical issues and repair guidelines
The main repair problems are related to the auxiliary power take-off equipment, torque dividers, and the main one – the cooling process or heat exchanger. Designers of these transmissions quite consciously reduced the transmission resource by means of cooling.
There are 3 main problems related to valve bodies of Allison 1000/2000/2400:
1. Sticking E-shift. When the valve sticks TCM detects that the pressure sensor doesn’t change the status and sets the trouble code P0872- after that the gearbox switches to the failsafe mode.
2. F-trim valve sleeve. The inside diameter of the sleeve wears out, leading to the torque converter clutch surge and trouble code P0741 – indicating the torque converter clutch slipping. . When lock-up stops operating and the P0741 code sets, the torque converter can overheat the ATF, causing damage to the torque converter and rapid deterioration of the ATF.
3. Warped castings. Valve bodies for these transmissions do not have separator plate gaskets, therefore it is required that two halves of the valve body should be flat sanded for protection from cross leakages. In this case locating pins should be removed to flat sand the valve body.Instruction manuals and useful links Suggest your link
| Link type | Source | Description |
|---|---|---|
| www | all-trans.by | Identifying Allison 1000/2000/2400 Valve Bodies |
| drive.google.com | Repair manual Allison 2000 | |
| drive.google.com | Repair manual Allison 2000 / Allison 2400 |