6F35 Zip Kit Transmission parts, repair guidelines, problems, manuals
Transmission general data
| Number of gears | Transmission Type | Drive | Torque (Nm) | ATF (full capacity) L | ATF (change) L | ATF type |
|---|---|---|---|---|---|---|
| 6 | AT | FWD/AWD | 350 | 8,5 | 4,8 | Valvoline MaxLife Multi-Vehicle ATF / Mercon LV/ Motorcraft XT-10-QLVC |
What are you looking for?
Overhaul Kit | Friction Kit | Friction | Steel Plate | Steel Kit | Band | Solenoid Kit | Solenoid EPC | Solenoid TCC | Pump | Shaft | Drum | Valve body | Torque converter | Hub | Piston | Piston Kit | Planetary Gear | Filter | Gasket | Bushing | Seal | Bearing | Pressure Plate | Stator | Differential | Retainer | Inhibitor Switch | Instruction manual | TOOLS & ACCESORIES | Sensor
Technical issues and repair guidelines
In most cases repair procedures f6F35 transmission consist of oil (DEXRON®VI or original XT-10-QLV) change and filter replacement. This transmission is very sensitive to the ATF level. It has no ATF level gauge and its levellevel is tested in compliance with the overflow stopper. As all 6-speed transmissions, the 6F35 (6F30) is sensitive to loads when the ATF is cold.
Many complaints have surfaced about erratic gear shifting, with gears harsh engagement and sometimes even slipping out of reverse or forward gear. The problem is most pronounced when the car is on the road, and happens when the transmission is stuck in one gear. It has been found that moving components within the transmission can create more friction, leading to issues requiring repair.
The 6F35 Transmission in Ford Fusion and Ford Perform cars is particularly prone to overheating issues. It is important to ensure that the control unit settings are adjusted appropriately, and also that the driver’s driving style is suitable for the vehicle. A dogged cooling system with less than optimal capacity has been found to depend on overall performance, so it may be worth removing Automatic Transmission Fluid (ATF) from the car.
This is one of the most common problems with 6F35 conventional 5-speeds transmission issues, and can be easily rectified by a keen driver. The 6F35 transmission offers better fuel economy than its conventional 5-speeds counterparts and covers their 6f35 cars in Ford, covering over 50,000 miles in some cases. It is also good for long run drivers as it provides a greater gear span and optimal speed load combinations with much better optimal combinations.
The 6F35 Transmission has a number of design flaws which can cause problems for drivers. One of the most common issues is that the transmission tends to drag engine rpm when shifting gears, especially when towing heavy loads. Another started problem is reluctance or little reluctance when starting off from a complete stop, especially on mountain roads or when driving in stop and go traffic on a Saturday afternoon. Towing is usually the most common cause of transmission problems as it runs the engine harder than normal and can cause significant wear on components over time. The 6F35 Transmission has been known to be reliable but certain design flaws can cause problems if not addressed properly.
One common issue is that the computer commanded 1st gear and 5th gear command will switch when read drive is commanded by the computer. This can be easily fixed by changing the range switch to read range switch and ensuring that the input speed sensor is operating properly. Another issue is when the shifter is moved, the rpm figure drops about 200 rpm from its original figure of around 2. This happens for a short time and can cause a few issues if it happens multiple times.
One of the most common 6F35 transmission problems is a failed one way clutch. This clutch can cause the wheel speed signal to be lost which will limit engine power and prevent the vehicle from moving. If this happens, it may be necessary to replace the converter. Additionally, if equipped with a problem vehicle, there may also be an issue with floor shift selector lever and display shifts. In some cases, it can even cause a push button start to not work correctly or no throttle response when starting the vehicle.
6F35 Transmission Problems And Possible Solutions can include malfunction valves, control valve, and the valve body separator plate. The malfunction can cause a compromise cooling in the heat exchanger. As a solution on transmissions, it is important to install a fluid heater in order to properly lubricate the transmission. Additionally, removing check ball is necessary to allow for proper flow of transmission fluid. It is also recommended to install a fluid cooler before any additional modifications are done. When using Mercon LV transmission fluid, it is important to note that the deleted hole must be drilled back into the valve body separator plate in order for it to pass proper flow of coolant from one side of the transmission dipstick tube over to the other side.
This external cooler bypass valve is necessary for the proper flow of coolant in order to prevent overheating and eventual transmission failure. If an experienced fluid leak is present, it can lead to a deteriorating fluid which compromises lubrication, leading to deterioration of internal components and eventually catastrophic failure of the transmission. Ford Fusion cars that are experiencing 6F35 transmission issues may be left with a failing left half shaft seal or other related issues if not addressed properly.
If you are having transmission problems, post your car in our cars section to see if others are having the same issues. Certain problems may be resolved with a simple transmission fluid flush or replacing the left half shaft seal. On our 2015 Ford Explorer, we had to completely rebuild the transmission and it was a costly endeavor. To keep track of any potential issues with your car, it is best to keep a log of when you drive your car and the mileage each time.
This can help you detect any problems with your 6F35 transmission early on. I recently had to repair my 6F35 transmission, and Ford sent me a rebuild kit to fix the inherent 6f35 problems. I took my car to the repair shop and they were able to use the kit from Ford to fix the problem. If you are not comfortable with fixing the issue yourself, I would advise you to take your vehicle into a dealership for them to look at it. They may be able to provide you with a powertrain warranty for any potential issues that may arise in the future. If this does not work, then Ford may even send your mechanic out a kit so they can use it in order to fix it up for you. However, this does not always guarantee that the problem will be fixed as some of their kits use faulty factory parts which could just postpone any inherent 6f35 problems until later down the line when they appear again.
In order to make sure that this doesn’t happen, it is a good idea to bring the car to a repair shop and have an experienced technician install the unit. The technician will also be able to use engine and transmission data as well as perform line pressure checks, hook pressure transducers, and hook cases to the mainline pressure port.
Write a review on this transmission, share your opinion.
Be the first one to leave your review!
Instruction manuals and useful links Suggest your link
| Link type | Source | Description |
|---|---|---|
| Sonnax | Vacuum test 6F35 (Gen. 1), 6F35 (Gen. 2) | |
| www | Sonnax | Solenoid Differences Between 6F35 Gen 1. & Gen. 2 |
| www | ATSG | 6F35 Repair Manual |
| Not specified | Unknown | Installation Guide for 6F35 |
| Not specified | Transmission Digest | 6F35 Overheating Issues Solution |
| Not specified | Sonar | Solving One-Way Clutch Failure on Ford 6F35 Torque Converter |